Honda Pioneer-UTV-Side x Side-Pioneer Parts-Accessories for sale

Honda Pioneer-UTV-Side x Side-Pioneer Parts-Accessories for sale

TWO PIECE POLY WINDSCREEN (HARD COAT) P/N 0SR71 HL4 A00 Instructions

CLICK HERE TO DOWNLOAD AND VIEW INSTUCTIONS 

 

Issue Date INSTALLATION INSTRUCTIONS Publication No. Honda Dealer: Please give a copy of these instructions to your customer. © 2015 American Honda Motor Co., Inc - All Rights Reserved. 0SR71-HL4-A00 1 of 5 Accessory Application PARTS LIST TWO-PIECE POLY WINDSCREEN (HARD COAT) P/N 0SR71-HL4-A00 SXS1000M/M3P/M5D/M5P MII 15262 September 2015 TOOLS AND SUPPLIES REQUIRED 4 mm hex wrench Torque wrench Power drill 5/16 inch (8 mm) drill bit TORQUE CHARTS Tighten all screws, bolts, and nuts to their specified torque values. Refer to the Service Manual for the torque values of the removed parts. Item N·m kgf·m lbf·ft 6 mm screw and nut 5 0.5 4 USE AND CARE INFORMATION • Check the accessory mount frequently and retighten if necessary. • Replace this accessory with a new one if it is damaged or discolored excessively. • When this accessory becomes dirty, rinse it thoroughly with cool water to remove loose dirt, then wipe with a clean cloth or sponge. • Do not use a brush to clean this accessory as it may scratch the surface. • Never use petroleum solvents such as gasoline, thinner, benzine, acid, or alkaline cleaners. No. Description Qty (1) Upper windscreen 1 (2) Lower windscreen 1 (3) Cam lock 5 (4) Hinge bracket 3 (5) Support bracket 1 (6) 6 x 16 mm screw 9 (7) 6 x 20 mm screw 1 (8) 6 x 25 mm screw 2 (9) 6 x 30 mm screw 3 (10) Left hinge arm 1 (11) Right hinge arm 1 (12) Left gasket 1 (13) Right gasket 1 (14) Clamp 2 (15) Nylock nut 2 (16) 6 mm flat washer 1 (17) Fender washer 2 (18) Flange collar 5 (19) 25 mm spacer 2 (20) 6 x 85 mm stud 2 (21) Trim clip 2 (22) Push dart 4 (23) Push nut 4 (24) Cam lever set 2 (25) Small spacer 1 (26) Large spacer 2 (27) Installation Instruction URL (not shown) 1 (1) (2) (10) (11) (12) (13) (16) (17) (18) (19) (26) (5) (14) (25) (20) (21) (9) (8) (7) (6) (22) (23) (3) (4) (24) (15) 2 of 5 0SR71-HL4-A00 © 2015 American Honda Motor Co., Inc - All Rights Reserved. INSTALLATION NOTE: • If installing a complete cab, install this accessory before installing the roof and door kits. • Remove and discard the rubber shipping band from the cam lock before installation of this accessory. SHIPPING BAND (DISCARD) ( 1. Install two cam locks to the lower windscreen using one 6 x 25 mm screw and spacer per cam lock. • Screws must be threaded into the hole in the base of the clamp as shown. CAM LOCK 6 x 25 mm SCREW SPACER GROMMET 2. Open the clamps on boths sides of the lower windscreen. 3. Place the lower windscreen onto the vehicle frame and seat the bottom edge onto the front hood. A-PILLAR WINDSCREEN 4. Install the support bracket to the inside of the lower windscreen using one 6 x 20 mm screw, one washer, and one small spacer. SUPPORT BRACKET WASHER 6 x 20 mm SCREW 5. Using the windscreen support bracket as a template, make a mark on the top of the instrument panel through both holes in the support bracket. 6. Remove the lower windscreen and drill holes through the marks on the instrument panel with a 5/16 inch (8 mm) drill bit. 7A. Place the Left and Right gaskets over the bottom corners of the lower windscreen, lining up the holes in the gasket and the windscreen. 7B. (CAB ONLY): If installing the windscreen as part of a hard cab system, carefully cut out the indented area of each gasket before installing it to the windscreen. GASKET (LEFT SHOWN) © 2015 American Honda Motor Co., Inc - All Rights Reserved. 0SR71-HL4-A00 3 of 5 8. Install the gaskets to the windscreen using two push darts and push nuts per side, as shown. PUSH NUT PUSH DART GASKET (LEFT SHOWN) 9. Reinstall the lower windscreen. Secure the lower windscreen to the instrument panel by placing trim clips through the windscreen bracket and into the holes. TRIM CLIP 10. Align the cam locks around the cab A-pillars and snap the arms closed. Do this on both sides. 11. Adjust clamp tension by rotating the threaded arm clockwise to tighten, counter-clockwise to loosen. THREADED ARM INSTALLATION - UPPER WINDSCREEN 12. Insert two 6 x 16 mm screws into the holes in the hinge bracket and then install them into the base of the cam lock as shown. 13. Insert one 6 x 16 mm screw through the hole in the cam lock and then intall it into the hinge bracket as shown. 6 x 16 mm SCREW CAM LOCK 6 x 16 mm SCREW HINGE BRACKET 14. Repeat Steps 12 and 13 for the remaining two hinges and clamps. 15. Install a hinge/cam lock assembly into each grommet using one 6 x 30 mm screw and flange collar, noting the orientation of the hinge/clamp assembly as shown. 6 x 30 mm SCREW GROMMET FLANGE COLLAR HINGE/ CAM LOCK 4 of 5 0SR71-HL4-A00 © 2015 American Honda Motor Co., Inc - All Rights Reserved. 16. Insert a lock nut into the the hinge arm bracket as shown. Insert a 6 x 30 mm screw through the hole in the left hinge arm and install it hand-tight into the lock nut. The hinge arm must rotate freely on the bracket. Repeat this process for the right hinge arm. HINGE ARM BRACKET 6 x 30 mm SCREW LEFT HINGE ARM LOCK NUT 17. Place the upper windscreen onto the cab frame with the bottom edge overlapping the top edge of the lower windscreen, and then close the cam locks. • Both windscreen sections should be touching each other along the entire overlapping edge. UPPER WINDSCREEN LOWER WINDSCREEN • To ensure proper fitment, close the cam locks once the gap between the edge of the windscreen and the A-pillars is even along the entire length of the frame. • Approximate angle of the upper cam locks shown. 18. Orient a clamp around the A-pillar just above the lower windscreen as shown and loosely install it using one 6 x 20 mm screw. • Do not tighten the bolt yet to allow for clamp position adjustments. 6 x 20 mm SCREW CLAMP 19. Line up the clamp adjacent to the top of the hinge arm and place a large spacer between both components as shown. Thread a stud through the hinge arm and the large spacer into the clamp as shown. Slide a spacer over the end of the stud and into the hinge arm slot as shown. SPACER STUD LARGE SPACER HINGE ARM 20. Install a washer and cam lever over the end of the stud as shown. Place the washer on first, then slide on the plastic base and thread on the cam lever. WASHER STUD CAM LEVER S U 21. Repeat Steps 18 through 21 on the right side. CLAMP PLASTIC BASE © 2015 American Honda Motor Co., Inc - All Rights Reserved. 0SR71-HL4-A00 5 of 5 • The overlapping edge between both the upper and lower sections of the windscreen should fit together as shown. 22. To open the “folding” windscreen, loosen the cam lever handles and push the upper windscreen forward. When the windscreen reaches the desired opening angle, tighten both cam lever handles.

Honda Two Piece Poly Windscreen Instructions

Honda Two Piece Poly Windscreen Instructions.

 

Click HERE to download the Honda Two-Piece Folding windshields instructions. 

Honda Pioneer 1000 5 Deluxe Bed Extender

New 2016 Honda Pioneer 1000 5 Deluxe Bed Extender kit for sale. 2016 Honda Pioneer 1000-5 bed extender for sale

Honda Pioneer 1000 5 Deluxe winch for sale

New Honda Pioneer 1000 5 Deluxe winch for sale online and at a discounted price get 18 % off your Honda Pioneer 1000 5 deluxe winch purchase. 

Honda 

Winch

Winch

$360.76

Retail $439.95

Honda 

Winch Mount

Winch Mount

$245.96

Retail $299.95


Honda Pioneer 1000 accessories for sale

Looking for the best deals on all your Honda Pioneer 1000 Accessories for sale then let Honda Parts King assist you in the best prices online. 

2016 Honda Pioneer 1000 OEM Parts For Sale

Discounted 2016 Honda Pioneer 1000 OEM Parts For Sale online. 

2016 Honda Pioneer 1000 for sale information price by dealer.

The all new 2016 Honda Pioneer 1000 is a side x side that is a contender for the new 2016 model year line up for the side x side industry. 

2015 Honda CBR 300 OEM Parts for sale discount prices fast shipping online.

** BEST DEALS ON ALL YOUR 2015 HONDA CBR 300 OEM PARTS** | 

Honda 2015 Motorcycle OEM Parts

Honda 2015 Motorcycle Original Equipment Manufacturer Parts at Honda Parts King



COMMON REPLACEMENT PARTS INCLUDE

AIR CLEANER
AIR INJECTION SOLENOID VALVE
ALTERNATOR
BALANCER SHAFT
BATTERY
CAM CHAIN / TENSIONER
CAMSHAFT / VALVE
CAUTION LABEL
CLUTCH
CRANKCASE
CRANKSHAFT / PISTON
CYLINDER
CYLINDER HEAD
CYLINDER HEAD COVER
FRAME
FRONT BRAKE CALIPER (STANDARD)
FRONT BRAKE MASTER CYLINDER (STANDARD)
FRONT FENDER
FRONT FORK
FRONT WHEEL
FUEL TANK
GEARSHIFT DRUM
HANDLE LEVER / SWITCH / CABLE
HANDLEBAR / TOP BRIDGE
HEADLIGHT
LEFT CRANKCASE COVER
MARK / STRIPE (CBR300R/RA-2A,2CM,3AC)
MARK / STRIPE (CBR300R/RA-8A,8CM,9AC)
MIDDLE COWL / UNDER COWL
MUFFLER
OIL PUMP
PEDAL
RADIATOR
REAR BRAKE CALIPER
REAR BRAKE MASTER CYLINDER
REAR FENDER
REAR SHOCK ABSORBER
REAR WHEEL
RIGHT CRANKCASE COVER
SEAT
SIDE COVER / REAR COWL
SPEEDOMETER
STAND
STARTER MOTOR
STARTING CLUTCH
STEERING STEM
STEP
SWINGARM
TAILLIGHT
THROTTLE BODY
TOOLS
TRANSMISSION
TURN SIGNAL
UPPER COWL
WIRE HARNESS
 
 
No matter where you live and you need the new 2014 and 2015 Honda CBR 300 OEM Parts We have you covered. Michigan-Ohio-Flordia-California-Texas-New Mexico.

Looking for Honda CBR Sport Bike OEM Parts and Accessories for sale online discount rates and fast shipping.

Honda Parts King has the best selection of new Honda Sport Bike Accessories. 

Select your Year and model below and save huge on all your Honda CBR and Goldwing accessories. 

 Select Within Honda Accessories:

We carry a large selection of Honda Accessories at Honda Parts King. To help us serve you better, please select your vehicle. From your selection, we'll match products that fit.

 

 

2015 Honda Pioneer 500 Windshield Discount shipping

2015 Honda Pioneer 500 windshields for sale 

 

 

Honda pioneer 500 windshields for sale fast shipping ! 

CALL ROBERT 1-866-554-4217 TO PRE ORDER THE HONDA PIONEER WINDSHIELD. 

 

Honda Parts King
5301 North US Hwy 27
St. Johns, MI 48879

Newsletter
Subscribe to our newsletter to receive our special email offers and more.
Share Honda Parts King